overlap integral中文什么意思

發音:

用"overlap integral"造句

重疊積分

overlap: vt.,vi. (-pp-) 1.(與…)交搭；疊蓋。 ...
integral: adj. 1.完全的；缺一不可的，主要的。 2.【數學】 ...
integral， overlap: 重疊積分
group overlap integral: 群重疊積分
overlap: vt.,vi. (-pp-) 1.(與…)交搭；疊蓋。 2.(與…)部分一致[巧合]，(時間等)重復，一致 (in)。 n. 1.重復，部分一致；交搭；重疊；復合。 2.覆蓋物，涂蓋層；【植物；植物學】蓋覆；【攝影】重榫攝影。 3.【數學】交疊，相交；復合。 4.【軍事】航空照片的重疊部分；【地質學；地理學】超復；累疊地層。

下載手機詞典可隨時隨地查詞查翻譯

例句與用法

The radiation loss was obtained from the imaginary part of the complex propagation constant and the transition loss was calculated by two - dimension overlap integral method
基于計算得到的直彎波導的模場分布，采用二維重疊積分法計算了兩者連接時的過渡損耗。
A theoretical study of input and output properties of four - level solid laser was performed according to the velocity equation , and the important role of the overlap integral j , was noticed and made a fully usage in optimizing the end - pumping solid state laser parameters such as : rod length > pump position pumping and oscillating beam waist size
從四能級速率方程出發，理論推導了ld端面泵浦的固體激光器的輸入輸出特性，并指出重疊積分j _ 1對激光器輸出特性的極大影響，從而對其在不同泵浦條件下進行分析并以此得到端面泵浦條件下固體激光器的最優化設計參數的選取方法。
The simulated results show that we can improve the sensitivity by setting the optical bias at / 2 , reducing the gap of electrode , increasing the overlap integral factor , reducing the insert lose , adopting suitable segmentation number , increasing the electrode length , increasing the optical power , reducing the wavelength and the relative intensity noise and reducing the receive bandwidth ; obtain the wider bandwidth utilizing reducing the electrode length and the capacitance of modulator , segmentation the electrode ; increase the dynamic range using lowering noise , increasing the optical power at the detector and lower optical bias
通過計算得知,使傳感器相位偏置為/ 2 ,減小電極間距,提高電光重疊因子,減小器件插入損耗,采用合適的分段數,增加電極長度,增大光功率,降低激光的波長,減小相對強度噪聲,減小接收帶寬,對提高靈敏度的效果是非常明顯的。而減小天線長度,降低調制器電容,電極分段,都可以獲取較大的帶寬。降低系統噪聲;增加到達探測器的光功率,采用較低的光學偏置,都可以增大線性動態范圍。
In this dissertation , the varied characteristics of soi rib waveguide were investigated , and the calculated results as well as simulated plots in theory were presented . it was the first time that a 3d overlap integral method was used to calculate the transition loss between the rib waveguides and the slab waveguides , in which the effect of the mode distribution in rib waveguides on the coupling efficiency was taken into account
針對上述問題，本論文對soi波導的各種特性進行探討并給出了詳細的計算結果，首次用三維功率交迭積分法計算了soi波導器件中波導過渡區的損耗，這種方法考慮了脊形波導模式分布對過渡區耦合效率的影響。
For the coupling between the laser diode and the tapered single - mode fiber , the overlap integral is used to compute the coupling efficiency on the basis that the laser diode outputting mode field and the fiber eigenmode field is approximated to basic - mode gauss field . and based on the same approximation , the coupling efficiency between the semi - tapered fiber and the laser diode is calculated by using the ray - traced method . the parameters are analyzed for the effect on the coupling efficiency and give the theory foundation to optimize the design of the tapered fiber coupling system
首先通過對半導體激光器輸出模式場和光纖本征模式場的高斯基模近似，利用交疊積分計算了錐形單模光纖與激光器的耦合效率問題；其次依據以上近似，利用光線跡蹤法計算了半錐形多模光纖與激光器的耦合效率問題，給出各個參數對耦合效率的影響和作用，為優化設計錐形光纖耦合系統提供了理論依據。